All propane suddenly not working : r/GoRVing

Jul 29, 2026

Leave a message

All Propane Suddenly Not Working: Complete 2026 RV Diagnosis & Solutions Guide

In this guide: Everything you need to know when all propane suddenly stops working - covering the most common causes, the 5-step regulator reset, how to diagnose dual-tank systems, what to check when everything goes out at once, when to call a professional, and the complete FAQ for 2026.


All Propane Suddenly Not Working: Quick Answer

When all propane appliances stop working at the same time, the cause is almost always in the propane supply system - not in the individual appliances. The most common causes in order of likelihood are: (1) regulator lockout after running a tank empty - fixed with the 5-step reset (turn off appliances, close tank valve, disconnect, wait 60 seconds, reconnect and open slowly, light while holding knob 30 seconds); (2) running out of propane on the active tank - switch to the other tank on dual-tank systems; (3) a faulty or frozen two-stage regulator - check for ice buildup and warm with a hairdryer; (4) a propane leak triggering the excess flow valve - perform a soap-bubble test on all fittings; (5) a tank valve that is not fully open. The single most important first step: turn off all propane appliances, then systematically work through the diagnosis below. If you smell propane gas at any point, evacuate the RV immediately and ventilate before investigating. Do not operate any electrical devices, lights, or appliances if you smell propane inside an enclosed RV.


Understanding Why Everything Goes Out at Once

The Propane Supply Chain

When all propane appliances stop working simultaneously, it is almost always a supply-side problem - the propane is not reaching the appliances. This is important to understand: if the furnace, water heater, stove, and refrigerator all stop working at the same time, the problem is not in four different appliances. The problem is in the common system they all share - the propane tank, regulator, or gas line.

The shared propane system in an RV: Every propane appliance in your RV draws from the same propane source through a common gas line:

Propane tank(s) → supply the propane

Two-stage regulator → reduces high tank pressure (250–350 PSIG) to safe appliance pressure (11 inches water column)

Gas distribution line → carries regulated propane to each appliance

Individual gas cocks → each appliance has its own shutoff valve

When the tank runs dry, the regulator locks, or the gas line is blocked, every appliance downstream loses gas at the same moment. This is why "everything going out at once" is always a supply-side diagnosis.

The exception - a furnace-specific shutdown: If the furnace is the only propane appliance that stops working while the stove and water heater still work, the problem may be in the furnace's own safety system (a thermal snap switch, high-limit switch, or pressure switch). If everything goes out simultaneously, start with the supply-side checklist below.


Step 1: The 5-Step Regulator Reset - The Fix for 80–90% of Cases

The Most Important RV Propane Procedure

The regulator is the most likely culprit when all propane stops working. The regulator contains a safety shutoff valve that closes when it detects abnormally low or fluctuating propane pressure - and it can be reset with the 5-step reset procedure.

When does the regulator lock out?

Running a tank completely empty (pressure drops to near-zero)

Swapping from an empty to a full tank without resetting

Opening the tank valve too quickly (pressure surge triggers the safety shutoff)

A sudden pressure change from temperature extremes

A minor blockage in the gas line

The 5-step RV propane regulator reset:

Step Action Detail
1. Turn off all propane appliances Set every appliance knob to OFF All burners, furnace, water heater, fridge
2. Close the propane tank valve Turn clockwise until fully closed Confirm the valve is fully sealed
3. Disconnect the propane connection Uncouple the gas line from the tank or regulator Separate the connection point
4. Wait exactly 60 seconds Leave the connection separated This allows the safety valve inside the regulator to reset
5. Reconnect, open slowly, and relight Reconnect fitting; open valve SLOWLY; light a burner and hold the knob pressed for 30 seconds Slowly opening the valve is critical

Why slow valve opening matters: Opening the tank valve too fast sends a pressure surge through the regulator that can re-trigger the safety lockout. Always count to 5 as you turn the valve from fully closed to fully open. This is the single most important prevention step.

If the reset works: All your appliances should function normally. Light each appliance following the manufacturer's procedure. Monitor for the next few hours - if the problem recurs after running normally, the regulator itself may be failing.

If the reset does not work after 3 attempts:

Check the other propane tank (on dual-tank systems)

Confirm the tank is not genuinely empty (weigh test)

Check every individual appliance gas cock is open

If the reset fails repeatedly, the regulator is likely faulty - professional replacement required


Step 2: Check Both Propane Tanks on Dual-Tank Systems

The Switchover Problem

Many RVs have two propane tanks - a primary and a secondary - and running out of propane on the active tank while the other is full is a common reason everything stops working.

How dual-tank RV systems work:

Both tanks connect to a shared fuel line through a two-tank switchover valve

The switchover valve automatically draws from the tank that has propane

When the active tank empties, the valve is supposed to switch to the reserve tank

If the switchover valve is faulty or both tanks are empty, everything stops

Diagnosing dual-tank problems:

Symptom Likely Cause Action
Both tanks appear full but no gas Switchover valve stuck or faulty Manually close one tank, open the other
Primary tank empty, reserve not feeding Switchover valve failure Replace switchover valve
Both tanks genuinely empty Both tanks need refilling Refill both tanks; perform 5-step reset
One tank valve is closed Inadvertent valve closure Open the closed tank valve
Auto-switchover not working Valve mechanism failure Manually operate the switchover

Manual tank switching procedure:

Close the primary tank valve (fully clockwise)

Open the reserve tank valve (fully counterclockwise)

Perform the 5-step reset

Test gas flow at a burner

Have the switchover valve inspected and replaced if faulty


Step 3: Check the Tank Level With the Weigh Test

Confirming the Tank Is Not Actually Empty

Before concluding the regulator is faulty, confirm the tank is not genuinely empty. The float gauge on a propane tank is unreliable - use the weigh test.

The propane tank weigh test for RVs:

Weigh the propane tank (bathroom scale or luggage scale works for portable tanks)

Find the tare weight (TW) stamped on the tank collar - typically approximately 17 lbs for a standard 20 lb RV tank

Subtract TW from total weight = propane weight

Propane weight ÷ 4.2 = gallons remaining

For a 20 lb tank, if total weight is under approximately 21 lbs, the tank is critically low

Tank level interpretation for a standard 20 lb RV tank:

Total Tank Weight Propane Level Status
34–36 lbs ~80% full Full - problem is elsewhere
30–33 lbs ~65–80% Good - monitor
25–29 lbs ~40–65% Getting low - refill soon
21–24 lbs ~20–35% Low - refill now
Under 21 lbs ~0–20% Critical - refill immediately

If the tank is empty: Refill or exchange it. After refilling, perform the 5-step reset before lighting any appliances. If the tank ran completely dry in cold weather, the regulator may have suffered damage and may need replacement.


Step 4: Diagnose Appliance-Specific Problems

When the Issue Is in One Appliance

If some propane appliances work and others do not, the problem is specific to the non-working appliance - not the system. Here is a quick guide:

Appliance Common Problem Quick Check
Furnace Safety switch tripped Find and press the reset button on the furnace control board
Furnace Blower not running Check the furnace fuse and motor relay
Furnace Thermocouple failed Furnace lights then goes out - thermocouple needs replacement
Water heater Gas valve closed Check the gas cock near the water heater
Water heater Spark/ignition failure Verify the spark igniter fires; check the gas valve
Refrigerator Gas cock closed Check the gas cock behind or beside the fridge
Refrigerator Thermostat not calling for cooling Raise the thermostat set point
Stove/oven Individual burner issue Try lighting each burner individually

If all appliances are off but propane should be flowing: The problem is in the common supply system. Return to Step 1 (the 5-step reset) and Step 2 (dual-tank check).


Step 5: Check for a Propane Leak

When the Problem Is a Leak, Not Empty Tanks

A propane leak in the RV gas line can trigger the excess flow valve - a safety device inside the tank valve that restricts gas flow when it detects an abnormally high flow rate (indicating a major leak).

Warning signs of a propane leak:

All appliances stopped working after hearing a hiss or propane smell

The problem started after an impact, bump, or road vibration event

One appliance was just repaired or the gas line was recently disconnected

The problem started during or after a tank swap

Immediate response for suspected leaks:

Evacuate the RV if you smell propane inside

Close all propane tank valves from outside the RV

Do not operate any electrical devices - lights, fans, phones

Ventilate from outside - open windows and doors

Perform a soap-bubble test on all connections: tank-to-regulator, regulator fittings, gas line junctions, appliance gas cocks

Soap-bubble leak test: Mix dish soap with water in a 1:1 ratio. Apply to every propane connection. Open the tank valve slowly. Any growing bubble indicates a leak at that connection. Tighten gently - overtightening damages O-rings.

If you find a leak:

Tighten the fitting gently

Retest

If the leak persists, replace the fitting or O-ring

If the leak is at the tank valve itself, replace the tank

If you cannot locate the leak or the leak is in the gas line, call a professional


Step 6: Cold Weather and Freezing Problems

Winter RV Propane Issues

Cold weather causes specific propane problems that can shut everything down simultaneously:

Problem 1: Regulator ice blockage Moisture in the propane system freezes at the regulator when temperatures drop below 20°F (-6°C), blocking gas flow. Symptoms: everything works when warm, stops when cold. Fix: warm the regulator with a hairdryer (never with an open flame). Prevention: use a propane de-icer additive and install a regulator cover ($10–$25).

Problem 2: Excess flow valve activation in cold The excess flow valve inside the tank valve can activate in cold weather when the pressure differential between the tank and gas line triggers it incorrectly. Fix: perform the 5-step reset. If it recurs, the valve may need professional service.

Problem 3: Propane pressure drop in extreme cold A tank at 0°F may not generate enough vapor pressure to operate all appliances simultaneously, even when partially full. Fix: move the tank to warmth (sunlight, heated compartment) or use a larger tank. This is a physics property of propane - not a malfunction.


When to Call a Professional

Red Flags That Require Expert Help

Stop troubleshooting and call an RV propane professional when:

Red Flag Why It Is Serious
You smell propane after closing all valves Active leak - potential explosion risk
The regulator or tank valve is damaged Risk of catastrophic gas release
You hear hissing from inside the gas line Possible underground leak in fixed gas line
The problem recurs after every refill Persistent system fault
A gas line was damaged in an accident Risk of underground rupture
The switchover valve is leaking Valve failure requires professional replacement
You cannot locate the source of a leak Hidden leak in fixed gas line
The problem started after a impact or road event Possible gas line damage from vibration or impact

RV Propane Sudden Failure Quick Reference

Diagnostic Table

What Happened Most Likely Cause Fix
Everything stopped after tank ran empty Regulator lockout 5-step reset
Everything stopped after tank swap Regulator lockout 5-step reset
Everything stopped - both tanks seem full Regulator lockout or faulty switchover 5-step reset; check switchover valve
Everything stopped after valve opened fast Excess flow valve triggered 5-step reset
Everything stopped in cold weather Regulator ice blockage Warm regulator; 5-step reset
Everything stopped after impact or road vibration Gas line damage or excess flow trigger Inspect gas line; 5-step reset
Everything stopped after you smell propane Propane leak triggered excess flow valve Close all valves; soap-bubble test
Everything stopped - one tank is empty Genuinely empty tank Refill tank; 5-step reset
Everything stopped - no propane smell, tanks full Regulator failure Professional replacement
Furnace only stopped, everything else works Furnace safety switch or blower Press furnace reset; check fuse

Frequently Asked Questions

Q1: Why did all my propane appliances stop working at the same time?

All propane appliances stopped working at the same time because they all share the same propane supply system - the tank, regulator, and gas line. When the propane supply is interrupted, every appliance downstream loses gas simultaneously. The most common cause of simultaneous propane failure is regulator lockout - the safety shutoff valve inside the two-stage regulator closes when it detects abnormally low or fluctuating propane pressure. This is typically triggered by running a tank empty, swapping tanks, or opening the tank valve too quickly. The fix is the 5-step reset: turn off all appliances, close the tank valve, disconnect the propane connection, wait 60 seconds, reconnect and open the valve slowly, and light a burner while holding the knob for 30 seconds. This resolves 80–90% of simultaneous propane failures. Other causes of simultaneous failure include: running out of propane, a faulty dual-tank switchover valve, regulator ice blockage in cold weather, or a propane leak triggering the excess flow valve.

Q2: How do I reset my RV propane regulator?

You reset your RV propane regulator with the 5-step reset procedure: (1) turn off all propane appliances - set every knob to OFF; (2) close the propane tank valve - turn clockwise until fully closed; (3) disconnect the propane connection - uncouple the gas line from the tank or regulator; (4) wait exactly 60 seconds - this allows the safety valve inside the regulator to reset; (5) reconnect, open the tank valve SLOWLY (count to 5), and light a burner while holding the knob pressed for 30 seconds. The most critical step is slow valve opening - opening the valve too quickly sends a pressure surge that re-triggers the regulator's safety shutoff. If the reset works, all your appliances should function normally. If it fails after 3 complete attempts, the regulator is likely faulty and needs professional replacement.

Q3: How do I know if my propane tank is actually empty?

You know if your propane tank is actually empty by using the weigh test - not the gauge. The built-in float gauge on a propane tank has an accuracy tolerance of approximately ±20% and is unreliable. To use the weigh test: weigh the tank on a bathroom or luggage scale; find the tare weight (TW stamped on the collar - approximately 17 lbs for a standard 20 lb tank); subtract TW from total weight = propane weight; divide by 4.2 = gallons remaining. For a 20 lb tank, a full tank weighs approximately 34–36 lbs. If the total weight is approximately 21–23 lbs or below, the tank is at or below 20% and should be refilled. If the total weight is approximately 21 lbs or under, the tank is critically low and may be empty enough to trigger the regulator lockout.

Q4: Why does my propane go out in cold weather?

Your propane goes out in cold weather because of three cold-weather propane problems: (1) regulator ice blockage - moisture in the propane system freezes at the regulator (which is the coldest point in the system) when temperatures drop below 20°F (-6°C), blocking gas flow; (2) reduced vapor pressure - propane's vapor pressure decreases as temperature drops; below approximately 60 PSIG, some appliances may not receive enough pressure to operate; (3) excess flow valve activation - cold weather causes a larger-than-normal pressure differential between the tank and gas line, which can trigger the excess flow valve inside the tank valve, cutting off gas flow. Solutions: use a regulator cover ($10–$25) and propane de-icer additive to prevent ice blockage; keep the propane tank warm (sunlight, heated compartment); perform the 5-step reset if the excess flow valve triggers; and know that a tank that works fine at 40°F may not perform at 10°F even when partially full - this is a physics property of propane, not a malfunction.

Q5: Should I call a professional if all my propane stops working?

Call an RV propane professional when: (1) you smell propane gas and cannot immediately locate and fix the leak - evacuate first, then investigate; (2) the regulator or tank valve is physically damaged - risk of catastrophic gas release; (3) the problem recurs after every refill - a persistent system fault requires diagnosis; (4) the gas line was damaged in an impact, accident, or road vibration event - underground gas line damage may not be visible; (5) the dual-tank switchover valve is leaking or not functioning - requires professional replacement; (6) you cannot locate the source of a propane leak - a hidden leak in the fixed gas line requires professional leak detection equipment; (7) the regulator is more than 10 years old and showing symptoms of failure. For the initial failure - especially if it occurred after running a tank empty or after a tank swap - the 5-step reset is the correct first step and resolves 80–90% of cases without a service call.


The Bottom Line

When all propane stops working at once, the problem is in the shared supply system - not the individual appliances - and the most common cause is regulator lockout after running a tank empty, swapping tanks, or opening the valve too fast. The 5-step reset resolves 80–90% of simultaneous propane failures: turn off appliances, close the tank valve, disconnect, wait 60 seconds, reconnect and open slowly, and light while holding the knob for 30 seconds. On dual-tank RVs, confirm both tanks are open and the switchover valve is functioning. Confirm the tank is not genuinely empty with the weigh test - the float gauge is unreliable. In cold weather, check for regulator ice blockage and warm with a hairdryer. If you smell propane, evacuate immediately, close all valves, and investigate with a soap-bubble test. If the reset fails after three attempts, a leak is suspected, or physical damage is found, call a professional. The single best prevention for sudden propane failures: open tank valves slowly every time, weigh tanks regularly, refill at 20%, and replace the regulator at 10 years.


Last updated: July 2026

Disclaimer: This guide provides general information about RV propane troubleshooting for educational purposes. Propane is a flammable gas - if you smell propane gas inside an enclosed RV, evacuate immediately, do not operate electrical devices, and call your propane supplier or 911. Never attempt to repair, modify, or replace propane system components without professional certification. Perform a soap-bubble leak test on all propane connections regularly. Inspect RV propane systems annually, especially before cold-weather camping. This guide is not affiliated with, endorsed by, or sponsored by any propane equipment manufacturer.

modular-1
OEM and ODM are available

Send your inquiry to us by whatsapp,email or contact here are ok.We can provide flow sensor,level sensor,leak detector,smart valve etc with your brand.

 

Send Inquiry