10-point-wifi-ultrasonic-water-level-controller-checklist-foam-tanks

Nov 01, 2026

Leave a message

10 Point WiFi Ultrasonic Water Level Controller Checklist: Foam Tanks

 

Foam tanks forgive fewer mistakes than clean-water tanks. The concentrate is viscous, it leaves a film, and a level controller mounted in the wrong spot on a foam station will misread within months. This ten-point checklist is the pre-buy walk-through we run with every buyer who calls about a foam tank. Work through it in order, and you will end up with a WiFi ultrasonic water level controller that reads the concentrate level for years, not weeks.

02-check1-tank-geometry

 

 

1. Confirm the tank type

Atmospheric concentrate tank, bladder pressure tank, or skid-mounted proportioner? The ultrasonic level sensor mounts differently on each. An atmospheric tank is the easy case; a bladder tank needs an ullage space and a flex-free wall; a skid needs the beam kept clear of the agitator. Note the type before you choose the level controller.

2. Measure the operating distance

Measure from the proposed mounting point down to the lowest concentrate level you must detect. A water level sensor rated 0.3–10 m covers most foam tanks. Buy the level controller by that distance, with margin - not by the tank's overall depth.

3. Keep the high alarm out of the dead zone

Every ultrasonic level sensor has a near dead zone, typically 0.3 m. If the high-concentrate alarm sits inside it, the reading goes uncertain just as the tank fills. Set the high alarm at least 0.3 m below the mounting face.

4. Aim the beam at a calm surface

Keep the ultrasonic beam clear of the inlet splash, the internal dip tube and any agitation. A water level sensor aimed at a turbulent fill point will report loss-of-echo faults. If the only clear spot is beside the inlet, accept the bracket offset and verify on commissioning.

5. Require relay logic, not just alerts

The foam tank needs a low-concentrate alarm, a high-level alarm, and ideally a relay that interlocks the proportioner when concentrate runs out. The level controller must deliver real relay outputs with adjustable hysteresis. An app-only notification is not protection.

6. Plan for the concentrate film

Concentrate leaves a residue on the transducer face. Choose a level controller whose face is wipeable from a reachable bracket, and write a face-clean into the annual service. This is not a defect in the level sensor; it is the maintenance reality of foam storage.

7. Specify the enclosure for the station

Foam stations sit in unheated pump houses and sun-baked skids. Require IP65 minimum per IEC 60529, IP67 if hosed down, and an operating range of roughly -20 °C to +60 °C. The WiFi level monitoring must survive both.

8. Check the WiFi at the mounting point

Stand where the level controller will bolt and check the 2.4 GHz signal with the phone. A concrete or metal tank attenuates the radio. If the signal is weak, plan an access point or repeater - and confirm the relay protection keeps working while the radio is weak.

9. Demand the audit history

Foam systems are serviced and audited. The cloud level monitoring must export the concentrate trend, so the service record shows the tank stayed above the refill level. A water level sensor with no history gives the auditor nothing.

10. Sample before you scale

Bench-test the level controller over a barrel, set the low and high setpoints, exercise the relay, cut the power, and confirm it reconnects to WiFi and remembers the setpoints. For a foam system that sits idle for years, a two-day sample is cheap insurance.

Why ten points, and not more

You could add twenty more, but these ten cover the failures we actually hear about: a high alarm in the dead zone, a beam aimed at the inlet, a face never wiped, a relay that only alerts, and a WiFi that cannot reach the skid. A foam tank level controller that passes all ten is a level controller you fit and forget.

The concentrate film, built into the plan

Point six in this checklist - the concentrate film - is the point that decides whether the foam-tank level controller lasts a decade. An ultrasonic level sensor exposed to concentrate vapour builds a residue on its face over months, and that residue shifts the echo timing. The fix is a wipeable bracket and an annual face-clean, not a different instrument. A WiFi ultrasonic water level controller mounted on a reachable bracket, with a face-clean written into the service plan, reads steadily for years; one mounted in a sealed tank top faults by month six.

The non-contact design still wins on foam tanks. A submersible water level sensor sits in the concentrate, its diaphragm fouls, and it drifts; the ultrasonic level sensor has nothing immersed, so there is no diaphragm to clean and no cable to degrade. The only maintenance is the face-wipe, which is why the ten-point checklist ends with the sample test rather than a hope.

The interlock point

A foam tank is a system to interlock, not just a level to watch. The low-concentrate relay should interlock the proportioner, so the foam system cannot run dry. The high-level relay should stop the fill. Confirm the level controller delivers real relay outputs for both, not just app alerts. A level sensor that only notifies leaves the proportioner running on empty; a relay-equipped water level controller stops it before the intake draws air.

 

modular-1

Request the configuration

Send us the foam tank drawing, the concentrate type and the tank type, and we will confirm the correct ultrasonic level controller range, mounting position and relay interlock. We will send the spec sheet with a sample and a quote.

 

 

 

Send Inquiry