Introduction
|
Disclaimer: This article references In-Situ Inc. as an example of professional-grade water level monitoring instruments. Specific product specifications, model numbers, accuracy ratings, and pricing vary. Always consult the official In-Situ product datasheets and your supplier for authoritative specifications. Representative specifications from In-Situ's published product range are used throughout. |
How Non-Vented Pressure Sensors Measure Water Level
The Hydrostatic Principle
The hydrostatic equation:
P_total = P_water + P_atm
P_water = rho x g x h
h = (P_total - P_atm) / (rho x g)
where: P = pressure (Pa), rho = water density (kg/m3), g = 9.806 m/s2, h = depth (m)
For fresh water: h (m) = (P_total - P_atm) in kPa / 9.806
Dynamic Density Compensation
Dynamic density compensation equation:
rho_actual = f(T, C)
where: T = water temperature, C = specific conductance (uS/cm)
Compensation adjusts the level calculation using measured T and C,
reducing density-dependent error to typically +/- 0.05% or better
Vented vs. Non-Vented: Which to Choose?
|
Factor |
Vented Sensor |
Non-Vented Sensor (Absolute) |
|
Barometric compensation |
Automatic - vent tube cancels atmospheric pressure |
Requires separate barometric reference (barologger) |
|
Cable design |
Vent tube required - more complex cable, risk of moisture in tube |
Single cable, simpler installation |
|
Deployment depth |
Limited by vent tube length - typically up to 300 m |
No practical depth limit |
|
Remote/telemetry use |
Requires vent tube routed to surface or vented logger |
Simpler - one cable to logger/telemetry |
|
Installation risk |
Vent tube moisture ingress causes measurement errors |
No vent tube - no moisture ingress risk |
|
Maintenance |
Vent tube must be kept dry |
No vent tube maintenance |
|
Typical use case |
Shallow wells, tanks, surface installations |
Deep boreholes, remote monitoring, all depths |
The In-Situ Water Level Instrument Family
Stand-Alone Water Level Loggers
|
Feature |
Representative Specification (In-Situ) |
Notes |
|
Housing material |
Titanium |
Corrosion-resistant in aggressive groundwater |
|
Pressure range |
0-30 m WC to 0-200 m WC (multiple ranges) |
Select to match maximum expected depth |
|
Accuracy |
Typically +/- 0.05% FS or better |
Dynamic density compensation improves accuracy further |
|
Temperature range |
0-50 C operating |
Storage: -40 to +80 C |
|
Battery life |
Up to 10 years |
Depends on logging interval and temperature |
|
Communication |
USB or inductive coupling (Win-Situ) |
Programmed and downloaded via Win-Situ software |
|
Online/telemetry |
Not available on 100-series |
Use 200-series for telemetry integration |
|
Water quality channels |
Pressure + temperature standard |
Aqua TROLL: adds conductivity |
Telemetry-Enabled Sensors
|
Feature |
Representative Specification |
Notes |
|
Communication protocols |
Modbus/RS-485, SDI-12, 4-20 mA |
All three standard industrial protocols supported |
|
Protocol advantage - Modbus |
Standard, widely supported by all SCADA/PLC systems |
Long cable runs (up to 1,200 m) |
|
Protocol advantage - SDI-12 |
Low-power, sensor-friendly for battery/telemetry |
Common in environmental monitoring |
|
Protocol advantage - 4-20 mA |
Industry standard for PLC/control systems |
Requires separate power conductor |
|
SCADA integration |
Direct connection to SCADA, PLC, or DCS |
No protocol converter needed |
|
Telemetry integration |
Compatible with cellular, radio, satellite modems |
Powers the modem directly in some models |
|
Use case |
Real-time monitoring, critical infrastructure, flood networks |
Data available without site visit |
Multiparameter Water Quality Instruments
|
Measurement |
Typical Range |
Accuracy |
|
Water level / pressure |
0-30 to 0-200 m WC |
+/- 0.05% FS (with density compensation) |
|
Conductivity |
0-100 uS/cm to 0-100,000 uS/cm |
+/- 0.5% of reading |
|
Temperature |
-5 to +50 C |
+/- 0.1 C |
|
Salinity |
0-70 ppt |
Derived from conductivity and temperature |
|
Total dissolved solids |
0-400,000 mg/L |
Derived from conductivity |
Deployment: Best Practices
Planning the Monitoring Campaign
Monitoring objective: Is this for short-term assessment (pump test, EIA), seasonal monitoring (6-12 months), or long-term compliance (multi-year)?
Access frequency: Can you retrieve the logger periodically, or is the site remote, requiring telemetry?
Data requirement: Do you need real-time data, or will periodic downloads suffice?
Well/borehole conditions: What is the total depth? What is the static water level? Is the well prone to surging or biofouling?
Water chemistry: Is the water fresh, brackish, or saline? Are there aggressive chemicals (low pH, high sulfide) that require special materials?
Installing a Non-Vented Level Sensor
Lower the sensor on the cable to the target depth - typically 1-2 m below the minimum expected water level. Never rest the sensor on the bottom of the well.
Anchor the suspension cable at a fixed reference point on the wellhead. The cable reference point is the zero datum for all level measurements.
Record the sensor depth below the reference point. Enter this as the deployment offset in the logger or telemetry software.
Deploy a barologger at the surface simultaneously if using non-vented absolute pressure sensors. The barologger must be at a location that represents the atmospheric pressure at the monitoring site - not inside a building with HVAC cycling.
For telemetry deployments: route the sensor cable to the telemetry system, connect to the Modbus/RS-485 or SDI-12 terminal, and verify communication before sealing the wellhead.
In aggressive water (low pH, high sulfide or chloride): verify the sensor housing and cable jacket material are compatible. Titanium housings provide the broadest chemical resistance.
Telemetry System Integration
Typical Modbus integration wiring:
Sensor (RS-485 A/B) ------> Telemetry Unit (RS-485)
Sensor Power (12-24 V DC) -----> Telemetry Unit (power output)
Modbus register map:
Register 40001: Water Level (m)
Register 40002: Temperature (C)
Register 40003: Conductivity (uS/cm, if equipped)
Register 40004: Barometric Pressure (kPa, if equipped)
Application Scenarios
Groundwater Monitoring Wells
River and Surface Water Gauging
Coastal Wetland and Estuary Research
Flood and Storm Surge Monitoring
Data Quality and Compensation
Barometric Compensation in Practice
|
Barometric Source |
Accuracy for Level Calculation |
Recommendation |
|
On-site barologger (concurrent deployment) |
Best - measures actual pressure at site |
Recommended for all critical monitoring |
|
Nearby weather station (within 5 km) |
Good - within 0.1-0.3 kPa in stable weather |
Acceptable for non-critical monitoring |
|
Distant weather station (>50 km) |
Poor - can be off by 1-2 kPa in weather fronts |
Not recommended for accurate level data |
|
Standard atmospheric pressure (101.325 kPa) |
Poor - ignores real atmospheric variation |
Never use for field monitoring |
Drift and Calibration
Field calibration procedure:
1. Measure water level with dip meter: D_dip (m)
2. Read logger/telemetry level: L_raw (m)
3. Calculate offset: Offset = L_raw - D_dip
4. Apply offset to all readings in the dataset: L_corrected = L_raw - Offset
5. Document the calibration date and offset in the data metadata
Selecting the Right Instrument
|
Requirement |
Recommended Instrument Type |
Key Consideration |
|
Short-term EIA, 90-day pump test |
Stand-alone logger (non-vented) |
No infrastructure needed; retrieve to download data |
|
Multi-year groundwater monitoring, remote |
Stand-alone logger (titanium, 10-year battery) |
Battery life critical; titanium housing for aggressive water |
|
Real-time monitoring, SCADA integration |
Telemetry-enabled sensor (Modbus/SDI-12) |
Direct SCADA connection; cellular or radio telemetry |
|
Environmental research, level + quality |
Multiparameter instrument (level + conductivity + T) |
Dynamic density compensation for accuracy in variable chemistry |
|
Coastal wetland, tidal, saline |
Multiparameter with titanium housing |
Dynamic density compensation; tidal data reveals saltwater intrusion |
|
Flood warning network |
Telemetry-enabled sensor + cellular/satellite |
Real-time data essential; solar power for remote sites |
|
Industrial tank monitoring, chemical |
Corrosion-resistant sensor + telemetry |
Verify chemical compatibility with housing and cable materials |
|
Storm surge monitoring |
Telemetry-enabled + high pressure range sensor |
Select range above maximum expected surge level |
