PLS Series Plastic Level Switches

Aug 03, 2026

Leave a message

PLS Series Plastic Level Switches

PLS Series plastic level switches is a family name used across several manufacturers for liquid level switches built in a plastic body - typically either a plastic reed-float switch (a magnetic float in a PP/PVDF/polysulfone housing) or a plastic optical switch (infrared total-internal-reflection at a prism tip). Because "PLS" is a series designation rather than one fixed part, exact voltage, output, temperature, and pressure depend on the specific maker and ordering code - always confirm on the datasheet. This guide covers what a PLS-series plastic switch is, the two common technology families, representative specifications, selection, and how it compares with sibling miniature models such as OS950, Optomax, LLE, and OS3.


What "PLS Series Plastic Level Switch" Means

PLS Series - a model-series prefix used by multiple suppliers for their plastic-bodied level-switch lines (one example is Preferred Utilities' PLS tank-level switch; many OEM catalogs use "PLS" for plastic float/optical switches).

Plastic - the wetting body is a polymer (PP, PVDF, or polysulfone), not metal, for corrosion resistance and low cost.

Level switch - a point device: it turns an output on/off when liquid reaches its setpoint, not a continuous gauge (see point vs continuous).

So a PLS-series plastic switch is a corrosion-resistant, low-cost point switch for water, chemicals, and mild process liquids.


Two Technology Families in the PLS Plastic Series

1. Plastic Reed-Float Switch

A hollow plastic float with a sealed magnet rides the liquid surface (vertical) or pivots (side-mount). At setpoints the magnet actuates an internal reed switch - a simple, reliable, no-power contact. Bodies are PP/PVDF/polysulfone; stems may be plastic or a non-wetted metal rod. See float switch overview and product types.

2. Plastic Optical Switch

A plastic prism tip uses IR total-internal-reflection: dry = light returns to the detector; wet = light escapes, so the detector registers water. No moving parts, solid-state NPN/PNP or IO-Link output. The OS950 miniature plastic optical and Optomax are this family; see also optical switches for liquids/tanks and the 5 advantages over float.

A single PLS series often offers both types so a buyer picks float or optical within the same plastic-body platform.


Representative Specifications (Verify per Datasheet)

Parameter Typical PLS-Series Plastic Range
Body material PP, PVDF, or Polysulfone (PSU)
Type Reed-float (vertical/side) or optical (TIR)
Supply (optical) 5–24 V DC (wide-range common)
Output (float) Reed contact (needs relay/PLC)
Output (optical) NPN / PNP 3-wire, sometimes IO-Link
Temperature −20 to +80 °C typical (PSU/PVDF to +125 °C on some)
Pressure Low (open-tank) to ~17 bar for reinforced bodies
Specific gravity (float) ≥ ~0.8 typical
Rating (optical) ~50–200 mA switch current
Mounting Thread, clip, or panel

These are representative; the exact numbers come from the specific ordering code. Use the datasheet guide.


How Each Type Works (Brief)

Reed-float: buoyancy lifts/drops the float; the magnet closes/opens the reed at setpoint. Simple, but needs a minimum specific gravity and can stick in debris.

Optical: IR at the prism tip reflects internally when dry and leaks into liquid when wet, toggling the solid-state output in milliseconds. See how optical sensors work.

Reed-Float Deep Dive (PLS Float Type)

The float obeys buoyancy: lift F = ρ × g × V, so it only rides the surface if the liquid's density beats the float's. Makers quote a minimum specific gravity (SG) - often ~0.8 - below which the float sinks and never trips. A slight hysteresis (the magnet closes on the way up at a hair different height than it opens on the way down) prevents chatter. PLS float bodies mount vertically (float slides a stem) or side/horizontal (float pivots on a hinge); some offer multi-point reeds on one stem for empty/low/ok/full. The reed is a passive dry contact - no supply needed, but current/voltage must stay within rating, and a relay or PLC inputs the load (see vertical float switches).

Optical Deep Dive (PLS Optical Type)

Three steps: (1) the IR LED shines into the prism tip; (2) in air the tip totally reflects the light back to the photodetector (state = dry); (3) when liquid wets the tip, the light's angle exits into the liquid, so the detector sees a sharp drop and the electronics output "wet." Because nothing moves, the switch is immune to float-stick and gives millisecond response. Heavy coating or oil film on the tip can shift the threshold, so keep the prism clean - for fouling media consider RF admittance or radar.

For high-precision DC-output background (NPN/PNP), see 12V/24V precision sensors.


PLS Plastic vs Sibling Miniature Models

Model Body Type Output Note
PLS-series plastic PP/PVDF/PSU Float or optical Reed or NPN/PNP Broad OEM family
OS950 Polysulfone Optical (mini) NPN/PNP Tiny, medical/OEM
Optomax Polysulfone Optical (digital) Open-collector/IO-Link Low-power digital
LLE Polysulfone Optical Solid-state Honeywell/SST; some discontinued
OS3 Metal (316L) Optical (industrial) PNP/NPN, IO-Link EX-rated option

The PLS series sits as the plastic-body, broad-coverage entry; OS950/Optomax/LLE are refined optical miniatures; OS3 is the metal/industrial/EX tier. The miniature optical roundup compares the optical miniatures directly.


Wiring & Outputs

Reed-float (PLS float type): the reed is a dry contact - switch a relay or PLC input, never the load directly. Polarity does not matter, but current/voltage ratings do.

Optical (PLS optical type): 3-wire DC - brown +V, blue 0 V, black signal; NPN (sinking) or PNP (sourcing) matched to the PLC input (same rule as proximity sensors). Contrast with float switch wiring.

Fail-safe: choose NO/NC so a broken wire or lost signal drives the safe state (stop pump / alarm).


Installation Best Practices

Float type: keep the stem vertical (or mount side units level per the drawing), use a guide tube in turbulent tanks, and allow free float travel with no obstruction.

Optical type: mount the tip flush with no trapped air gap - an air pocket defeats TIR and reads false "dry." Avoid bubbles and turbulence at the tip.

Both: seal the body/thread, not the sensing tip; route cable away from power to reduce noise; verify polarity before energizing the optical type.

Multi-point: space float reeds or multiple optical units for the levels you need (empty/low/ok/full).

See float switch wiring for control logic and tank automation for setpoint use.

Troubleshooting

Symptom Likely Cause Fix
Float never trips Liquid SG below minimum Use a higher-buoyancy float or optical
Float sticks Debris / slime Clean; consider optical
Optical no switch Wrong polarity / air gap Check brown/blue; remount flush
Optical stuck wet Coating/oil on tip Clean prism; non-contact tech if chronic
Chatter Turbulence / marginal SG Relocate; confirm SG margin

Why a Plastic Body? Chemical Compatibility

Plastic Resists Avoid
PP (polypropylene) Water, mild acids/alkalis, cleaners Strong solvents, aromatics, high temp
PVDF Acids, many solvents, higher temp Strong bases, ketones (check)
PSU (polysulfone) Water, oils, steam-clean, wide use Ketones, chlorinated solvents

Match the body to the fluid, not the brand. For non-optical alternatives see float vs capacitive and magnetic float switches.


Selection Checklist

Point or continuous? PLS is a point switch - choose continuous if you need exact level.

Float or optical? Float = simple, needs SG margin; optical = no moving parts, fast, clear liquids.

Body material. PP/PVDF/PSU vs your chemistry and temperature.

Supply & output. 5–24 V; reed vs NPN/PNP/IO-Link to the controller.

Temperature/pressure. Confirm vs duty (steam? pressurized line?).

Specific gravity (float). Ensure the float works at your liquid's SG.

Hazardous area? Use a certified model (hazardous guide).

Fail-safe & mounting. NO/NC, thread/clip/panel, tip flush (optical).

Our choosing the right switch maps these to products; vertical float switches cover the float mounting detail.


Where PLS Plastic Switches Are Used

Application Why Plastic PLS
Water tanks & appliances Cheap, corrosion-free, food-safe PP
Chemical & plating PVDF/PSU resist acids
Aquarium / hydroponics Small, low-voltage, safe
Medical / lab OEM Polysulfone, steam-cleanable
Food & beverage Smooth plastic, cleanable
Cooling & HVAC Resists treated water

Common Mistakes

Assuming one "PLS" spec fits all. The series spans float and optical with different codes - verify the exact part.

Skipping chemical check. PP fails on solvents; pick PVDF/PSU for harsh media.

Float SG too low. The float needs a specific-gravity margin; thick liquids may not lift it.

Powering load from a reed/optical. Use a relay/PLC stage.

Mismatching NPN/PNP to the PLC input.

Forgetting fail-safe NO/NC on a critical pump or alarm.


FAQ: PLS Series Plastic Level Switches

What is a PLS Series plastic level switch?

A family of plastic-body liquid level switches (reed-float or optical) from several makers, used as low-cost, corrosion-resistant point switches.

Is PLS one specific product?

No - "PLS" is a series designation used by multiple suppliers; exact specs depend on the ordering code. Confirm on the datasheet.

What types come in the PLS plastic series?

Usually both a plastic reed-float switch and a plastic optical (IR) switch within the same body platform.

Are they continuous or point?

Point - they switch at a setpoint. For exact level use a continuous sensor.

What output do they have?

Float types give a reed contact (via relay/PLC); optical types give NPN/PNP or IO-Link.

Which plastic body should I choose?

PP for water/mild chemistry, PVDF for acids/solvents, polysulfone for broad use and steam cleaning.

Do they need power?

Optical types need 5–24 V DC; reed-float types are passive contacts (the load circuit supplies current).

Can a float type handle dirty water?

It can, but debris may stick the float - optical or a shielded design may be better.

Are they safe for hazardous areas?

Only if the specific model is certified (ATEX/IECEx). See the hazardous guide.

How do I wire the optical type?

Brown +V, blue 0 V, black signal; NPN to a sinking input, PNP to a sourcing input.

How is PLS different from OS950/Optomax?

PLS is the broad plastic-body family (float or optical); OS950/Optomax are refined miniature optical models. See the roundup.

What is the temperature limit?

Typically −20 to +80 °C, with PSU/PVDF versions to ~+125 °C on some codes - verify per part.

Can I use it for exact tank volume?

No - it is a point switch. Multiple units at heights give coarse multi-point level only.

What specific gravity does the float need?

Most PLS float types need SG ≥ ~0.8; check the datasheet. Thick or low-density liquids may need a special high-buoyancy float or an optical type.

Why won't the optical switch trigger?

Usually wrong polarity/supply, an air gap at the tip, or a coating on the prism. Verify wiring, remount flush, and clean the tip.


Conclusion

PLS Series plastic level switches are a practical, corrosion-resistant family of point-level devices built in PP, PVDF, or polysulfone - available as either plastic reed-float switches (simple, passive, SG-dependent) or plastic optical switches (no moving parts, fast, solid-state NPN/PNP/IO-Link). Because "PLS" spans multiple makers and codes, treat the specifications above as representative and confirm the exact part on its datasheet. Choose float for simplicity or optical for reliability and clear liquids, match the plastic to your chemistry and temperature, drive the load through a relay/PLC stage, set NO/NC for fail-safe behavior, and step up to a metal/EX model like OS3 when the environment demands it. For exact level, pair with a continuous sensor; for the optical miniatures, see OS950 and Optomax.

For more, see float switch overview, product types, vertical float switches, magnetic float switches, float wiring, OS950, Optomax, LLE, OS3, optical switches, 5 advantages over float, liquid vs solid detection, float vs capacitive, point vs continuous, precision 12V/24V, choosing the right switch, hazardous guide, and the ultimate guide.

Send Inquiry